The Foundation of Plumbing Skills When Installing a Bathtub
The Foundation of Plumbing Skills When Installing a Bathtub
Blog Article
The article author is making several good pointers related to Installing A Bathtub in general in the article followed below.
Installing a tub isn't exactly brain surgery, however it does need strong plumbing, carpentry, and also sometimes, tiling abilities. Changing an old bathtub with a new one is likewise a moderately difficult task. If the old bathtub is readily easily accessible, the job can relocate rapidly; if you need to open up a wall to get rid of the old bathtub as well as place the brand-new bath tub, the job is a lot harder. In either situation, the task is within a house handyman's abilities, although you will certainly require an assistant to vacate the old tub and also set in the new one. See to it you have certified on your own for the job as well as fit attempting it. Instead of employing a contractor to take control of a halfway-completed task, it is much better to consider utilizing one before you start. Opportunities are you may need a specialist plumber to make tube links.
This post will certainly assist you set up a new bathtub in your restroom if you have currently gotten a brand-new bathtub and do not need to change the setup of your previous water pipes.
Your tools and also material list need to make up the following:
Getting ready for the Installment
Firstly, the sustaining frame supplied with the bathroom ought to be fitted (if called for) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is necessary to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets device to prevent pressure on the bath tub.
Fit the flexible faucet adapters to the bottom of the two taps utilizing 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you make use of every one of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath must now be ready to be fitted in its final setting.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your setup, then the first thing you should do is disconnect the water. After doing so, turn on the taps to drain any type of water remaining in the system. The procedure of eliminating the existing faucets can be quite problematic as a result of the limited accessibility that is often the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the taps. Have a towel prepared for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have been removed, make use of the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from turning during this procedure. Once the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any kind of old securing substance.
Prior to proceeding to fit the new faucets, contrast the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the brand-new taps to fit.
Setting up the Bathtub
Using the two wooden boards under its feet, position the tub in the needed position. The wood boards are practical in evenly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 small factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by checking the level as well as changing the feet on the bathtub till the spirit level reads level.
To set up taps, fit the bottom of the outermost versatile tap port to the appropriate supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Turn on the supply of water and also inspect all joints as well as new pipework for leaks and also tighten them if essential. Load the bath tub as well as also examine the overflow electrical outlet as well as the typical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and also sealing around the bath tub must wait till the tub has actually been utilized a minimum of once as this will resolve it into its last setting.
Fitting New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic port to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washers are in area in between the tap as well as the sink. Secure the faucet in place with the supplier provided backnut. As soon as the tap is securely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous type must be linked to the tap finishes first, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the area where the bath fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to fracture a rigid seal, causing the water to penetrate the wall between the bath and the tiling, leading to problems with moisture and possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to blend in your components as well as fittings. They are offered in tubes as well as cartridges, and also are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of drenched paper or soft rope. Remember to constantly fill up the bath tub with water before securing, to permit the activity experienced when the tub remains in usage. The sealer can crack rather early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently available on the marketplace. It is a good idea to fit the tiles making use of waterproof or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed reading our section on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks a lot for taking time to browse our posting. You should take a moment to distribute this post if you enjoyed reading it. Thanks for taking the time to read it.
Contact for quality! Report this page